Subversion Repositories group.electronics

#include <avr/io.h>

#include <avr/wdt.h>

#include <avr/interrupt.h>

#include <string.h>

#include <util/delay.h>

#include <stdlib.h>

#include "config.h"

#include "avrutil.h"

#include "hc595.h"

#include "twires.h"

#ifndef NULL

#define NULL    ((void *)0)

#endif

#ifndef PROTOTYPE

#define PROTOTYPE

#endif

void writeSegment(uint8_t digit, uint8_t value);

void pcInterrupt(void);

void receiveEvent(uint8_t bytes);

/* ------------------------------------------------------------------------- */

#ifndef TWI_RX_BUFFER_SIZE

#define TWI_RX_BUFFER_SIZE ( 16 )

#endif

volatile uint8_t user_debug = 0;

volatile uint8_t tmr0_ovf = 0;

volatile struct {

        uint8_t current;

        uint8_t last;

        uint8_t mask;

} pcInt;

volatile struct {

	int8_t outer;

	int8_t inner;

} input;

//volatile uint8_t doInt = 0;

//uint8_t disVal[] = {8,8,8,8,8,8,8,8,8,8};

volatile uint8_t disVal[] = {0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a};

volatile uint16_t disPt = 0x00;

int main(void) {

  /*

  DDR : 1 = Output, 0 = Input

  PORT: 1 = Pullup for Input, otherwise set output

  PIN : Read input pin

  */

  /*

	PA0 -	Output		- HC595 DS

	PA1 - 	Output		- HC595 ST

	PA2 -	Output		- HC595 SH

	PA3 -	Output		- 4511 blanking

	PA4 -	SCK

	PA5 -	Output		- Decimal Point

	PA6 -	SDA

	PA7 -	Input, Pullup	- Flip button

  */

  DDRA          = 0B00101111;

  PORTA         = 0B10001000;

  /*

	PB0     - Input, PCInt, Pullup	- Rot1a

	PB1     - Input, PCInt, Pullup	- Rot1b

	PB2     - Input, Pullup		- Swap button

	PB3     - N/A			- Reset (Future - I2C address select)

  */

  DDRB          = 0B00000000;

  PORTB         = 0B00000111;

    systime = 0;

    sysclockInit();

    PCMSK1 |= (( 1 << ROT_1A_PIN ) | ( 1 << ROT_1B_PIN ));

    GIMSK |= (1 << PCIE1);

    pcInt.last = ROT_1_PIN;

    pcInt.current = pcInt.last;

    pcInt.mask = 0;

    twires_begin(I2C_SLAVE_ADDR);

    twires_onReceive(receiveEvent);

    wdt_enable(WDTO_1S);	// Watchdog for 1 sec

    sei();			// Enable interrupts

    uint32_t refresh = systime;

    uint8_t disIdx = 0;

    // Init and clear the displays

    hc595_init();

    hc595_write(0x00);

    for(;;){

    	 wdt_reset();

    	if (user_debug) {

    		disVal[9] = rbi(SB_INPUT, SB_PIN);

    		disVal[8] = rbi(FB_INPUT, FB_PIN);

    		disVal[0] = input.outer & 0x0f;

    		disVal[1] = input.outer >> 4;

    	}

		if (pcInt.current != pcInt.last) {

			cli(); 		// Dont process interrupts for a bit

			pcInterrupt();

			sei();

		}

		if (systime > refresh) {

			writeSegment(disIdx, disVal[disIdx]);

			refresh = systime + DISPLAY_REFRESH;

			disIdx++;

			if (disIdx > 10) disIdx = 0;

		}

		twires_stop_check();

    }

    return 0;

}

void receiveEvent(uint8_t bytes) {

	uint8_t cmd = twires_receive();

	bytes--;

	switch (cmd) {

		case (0x01): {

			// Send 2 bytes with version details

			twires_send(HW_VERSION);

			twires_send(SW_VERSION);

		}

			break;

		case (0x03): {

			// Enable debugging mode

			user_debug = twires_receive();

		}

			break;

		case (0x05): {

			// Receive n numbers of digits to DISPLAY_REFRESH

			// High nibble = segment number

			// Low nibble = digit to display

			while (bytes--) {

				uint8_t data = twires_receive();

				disVal[(data >> 4)] = (data & 0x0f);

			}

		}

			break;

		case (0x08): {

			// Recieve 2 bytes, for the decimal points

			//  5 bits used in eac byte

			disPt = (uint16_t)twires_receive() << 8;

			disPt |= (uint16_t)twires_receive();

		}

			break;

		case (0x09): {

			// Reset the rotary

			input.outer = 0;

			input.inner = 0;

		}

			break;

		case (0x0a): {

			// Send the value of the rotary count

			twires_send(input.outer);

		}

			break;

		/* Not used in this version

		case (0x0b): {

			twires_send(input.inner);

		}

			break;

		*/

		case (0x0c): {

			// Send that status of the buttons

			uint8_t out = (!rbi(SB_INPUT, SB_PIN)) << 1;

			out |= (!rbi(FB_INPUT, FB_PIN));

			twires_send(out);

		}

		/* Comined into 0x0c

		case (0x0d): {

			twires_send(rbi(FB_INPUT, FB_PIN));

		}

			break;

		*/

		default: {

			// Don't know what it is, empty buffer

			while (twires_available())

				twires_receive();

		}

			break;

	}

}

void writeSegment(uint8_t digit, uint8_t value) {

	//uint8_t dp = 0;

	//if (digit <= 4 && rbi(disPt[0], digit)) dp = 1;

	//if (digit > 4 && rbi(disPt[1], digit-5)) dp = 1;

	cbi(BL_PORT, BL_PIN);			// Blank the 4511

	cbi(DP_PORT, DP_PIN);			// Drop the DP before changing digit

// Changed my mind and reversed order of digit display for release version

//   0-9 is left to right on release, right to left on prototype

//   This below hack for the prototype means i didn't have to change the ls145n

//	 connections, but have been changed on the release version

#ifdef PROTOTYPE

	hc595_write((value << 4) | (9-(digit & 0x0f))); //Write the value and digit

#else

	hc595_write((value << 4) | (digit & 0x0f)); //Write the value and digit

#endif

	if (rbi(disPt, digit)) sbi(DP_PORT, DP_PIN);		// Add DP if required

	sbi(BL_PORT, BL_PIN);			// Enable the 4511

}

void pcInterrupt() {

	pcInt.mask = pcInt.current ^ pcInt.last;

	pcInt.last = pcInt.current;

        if (!pcInt.mask)

        	return;

        // Check which pin caused the interrupt. If they both

        //  equal 0 || 1, the pin that interrupted is the direction

        if (((rbi(pcInt.current, ROT_1A_PIN) == 1 &&

             rbi(pcInt.current, ROT_1B_PIN) == 1) ||

             (rbi(pcInt.current, ROT_1A_PIN) == 0 &&

              rbi(pcInt.current, ROT_1B_PIN) == 0))) {

        	if (rbi(pcInt.mask, ROT_1A_PIN) ) {

        		input.outer -= 1;

              } else if (rbi(pcInt.mask, ROT_1B_PIN) ) {

            	input.outer += 1;

            }

        }

        // Clear the mask so we know we've dealt with it

        // Shouldn't be required now that 'doInt' has been removed

        //pcInt.mask = 0;

}

ISR(PCINT1_vect) {

	pcInt.current = ROT_1_PIN;

}

ISR(TIM0_OVF_vect) {

    tmr0_ovf++;

	// Clk/1 TCCR0B = (1<< CS00);

	//20.0Mhz, 1ms = 78ovf

	//16.5Mhz, 1ms = 64ovf

	//16.0Mhz, 1ms = 62ovf

	//12.0Mhz, 1ms = 46ovf

	// 8.0Mhz, 1ms = 31ovf

	// 8.0Mhz, .5ms = 15ovf, 160r

	if (tmr0_ovf>=15) {

			systime++;

			tmr0_ovf = 0;

	}

}